


Expansion Module 4 Relays 4 Inputs
The ControlByWeb X-17S™ expansion module is used with either the X-400™ or X-600M™ controllers. The 4 onboard relays have Form-A contacts (SPST) and can be used to control moderate loads. Each input is optically isolated and allows the grounding system of equipment and the low-voltage circuits of the X-17S to be electrically separate. One or more X-17S expansion units can be connected with a ribbon cable that provides both power and communications via the BUS.
- 4 Relays
- 4 Digital Inputs
- Expansion Module for the X-400 and X-600M
- Description
- Features and Applications
- Specifications
- Downloads
Description
The Smart Go-To for Remote Applications
The ControlByWeb X-17S is a highly versatile expansion module, offering the flexibility to monitor sensors and control devices over a network when paired with the X-400 or X-600M. Common applications include center pivot, simple tank monitoring, and moderate-light loads like solenoid valves, alarms, and indicator lights.
X-17S Features
- Four isolated relays (SPST)
- Relay Functions: On, Off, Pulse
- Four optically-isolated digital inputs (common negative)
- Input Functions: On/Off Status, Pulse Count, Pulse Duration, Accumulated Pulse Time, Frequency
- Powered through expansion bus (no separate power supply connections are required)
- Eight LEDs for inputs and outputs
- Removable terminal connector
Power Requirements
- Voltage: 9-28 VDC (supplied via the X-400 or X-600M controller, 24V recommended)
- Max Current: See table below for typical values at 25°C.
Power Supply | All Opto-couplers & Relays OFF | All Opto-couplers & Relays ON |
---|---|---|
9 VDC | 18 mA | 224 mA |
12 VDC | 14 mA | 165 mA |
24 VDC | 8 mA | 86 mA |
Relay Contacts
- Number of Relays: 4
- Max Voltage: 125VAC, 30VDC
- Max Current: 2.5A
- Contact Type: SPST (Form A)
- Load Type: General purpose
- Contact Resistance: < 100 milliohms initial
- Contact Material: AgSnO2
- Electrical Life: 100K operations (Min)
- Mechanical Life: 5M cycles (Min)
- Environmental Rating: Over voltage Category II, Pollution Degree 2
- Relay Modes: On/Off or Pulsed
- Pulse Timer Duration: 0.1 to 86,400 Seconds (1-day)
Digital Inputs
- Number of Inputs: 4
- Type: Optically-Isolated
- Voltage Range: 3-26VDC
- Current: 0.6mA @ 3V, 8.2mA @ 26V
- Minimum Hold Time: 2.5mS
- Input Isolation: 1500V
- Input Functions: Monitor State, Control Relays, Control Remote Relays, Count, Frequency, High Time, ON Time
- Maximum Count: 32-bit
- Max Count Rate: 200Hz
- Edge Trigger: Rising, Falling or Both
- High Time: Pulse width (4,194,304 seconds max)
- On Time: Accumulated time an input is asserted (4,194,304 seconds max)
- Frequency: 1 Hz min, 200 Hz max
Connectors
- Relays & Inputs: 14-Position, 3.81mm terminal spacing, Removable. For 16-28 AWG wire.
- Expansion Connector: Ribbon cable, 10-conductor, polarized, 2×5-position, 0.100″ pitch Provides power and communications for expansion modules (Communications: RS-485)
LED Indicators
- Number of LEDs: 9
- Power on
- Relay coil energized 1-4
- Digital Inputs 1-4
Physical
- Size:
- 1.41in (35.7mm) wide
- 3.88in (98.5mm) tall
- 3.1in (78mm) deep (not including connector)
- Weight: 4.8 oz (136 g)
- Enclosure Material: Lexan 940 Polycarbonate Plastic
- Enclosure Flame Rating: UL94 V0
Environmental
- Operating Temperature: -40°F to 150°F (-40°C to 65.5°C)
- Storage Temperature: -40°F to 185°F (-40°C to 85°C)
- Humidity: 5-95%, non-condensing
- Altitude: Up to 2,000m
- Indoor use or NEMA-4 protected location
Electromagnetic Compliance
- IEC CISPR 22, CISPR 24
- FCC 47CFR15 (Class B)
- EN55024 ITE Immunity (2010)
- EN55022 Emissions (2010)
Product Safety Compliance
- IEC 61010-1
Datasheet x-17s